-

Как получать данные с инфракрасного ИК порта в . LIRC serial not working - Page 2 - Ubuntu Forums

However, if you know what protocol your remote uses (RC5, RC6, etc), you can copy the protocol header file as /etc/lircd.conf and irrecord (when not in raw mode) will try to use that to understand your remote.

Можно посмотреть сигнал в графическом виде:xmode2 -d /dev/lirc0Если этот шаг нормально выполнится, то отконфигурировать LIRC не представляет труда.

Bottom line, when the "rc_core" module is loaded it includes many components, some of which has no meaning to your system.

$Id: lirc_serial.c,v 5.89 2008/04/06 19:03:52 lirc Exp .

Вроде на старых линухах можно было переключиться в первую консоль где шла загрузка, и кнопками ctrl+PgUp подняться вверх.

S0 >> cat: /dev/ttyS0: Input/output error > Если порт уже занят другим процессом ничего другого и не получишь Нет, дело видимо в другом.

Возможно стоит поробовать загрузить все модули lirc.anonymous (28.05.2008 17:27:11)Re: Самодельный IR приемник и LIRC.

mechanic: LIRC + Mandriva 2007.0 Северо-Кавказская Группа .

Both of the following shows nothing:⟫ irw⟫ sudo mode2 -d /dev/lircdThe remote itself works, as I can see another device reacting to the pulses from the the remote.

But the warning is a red herring because it is the right code and when you install with apt-get there is no other option for where to get the code.

Впринципе, теперь осталось сделать две вещи - чтобы модули и демоны грузились при старте системы, и правильно написать /dev/lirc/lircmd.conf чтобы команды с пульта выполнялись в нужных приложениях. list all known serial killers

More 1 : 0); printk(KERN_INFO LIRC_DRIVER_NAME ": auto-detected active " "%s receiver\n", sense ? "low" : "high"); } else .,[ 170.749628] lirc_serial: auto-detected active high receiver [ 170.749643] lirc_dev: lirc_register_driver: ., . on each load also and always came after the line lirc_serial: auto-detected active high receiver .

More [ 282.209388] lirc_serial: auto-detected active high receiver [ 282.209400] lirc_dev: lirc_register_plugin: ., Wenn dmesg die Meldung "lirc_serial: auto-detected active high receiver" zeigt, liegt irgendein ., . 0 kernel: lirc_serial: auto-detected active low receiver new dmesg (with debug enabled): . lirc_serial registered at minor = 0 I forced active low because it was reporting active high, .

More lirc_serial hardware does not support sending . lirc_serial: auto-detected active high receiver, [ 5.348020] lirc_serial lirc_serial.0: auto-detected active high receiver [ 5.348095] lirc_serial ., The driver is actually a modification of the lirc_serial . lirc_rpi: auto-detected active low receiver on GPIO pin 18 . TSOP2238, TSOP2438, *TSOP4838, * TSOP4438 (active highlow .

FS#21283 : [lirc] 0.8.6-7 don't work with serial receivers - Arch Linux

In this case the only thing I did differently was the additional dpkg extraction and partial install of the config files.

UNIX-CONNECT:/dev/lircd STDIOAnmerkung: Falls irw ordnungsgemäß funktioniert und der VDR fehlerfrei LIRC aufruft, die Fernbedienung aber dennoch nicht im VDR funktioniert, vergewissert Euch, dass /etc/lircd.conf und remote.conf auch wirklich die gleichen Namen der Tastenbelegungen haben.

Handy-друг молодёжи...     Наши тусовки         Allrussian путешествует..     Голос с трибуны или пару слов о спорте         Allrussian Tipprunde     Творческий коммуникатор     Авто...

Related articles

And the third, which would repeat over and over and over said lirc_serial: ignoring spike: 1 0 4d982d7d 4d982d7d 410ed 410a8 where the 4 hex values changed for each line, presumably telling me .lirc_serial ignoring spike 1 1.
[1292746.588538] lirc_serial: ignoring spike: 1 1 4fd56036 4fd56036 8e9d8 8e4ab [ 1292746.588647] lirc_serial: ignoring spike: 1 1 4fd56036 4fd56036 8ea49 8ea44 [1292746.588716 . lirc_serial: auto-detected active low receiver lirc_dev: lirc_register_plugin: sample_rate: 0 lirc_serial: ignoring spike: 1 1 4a3cdfee 4a3cdfee 9b369 9b335 lirc_serial: ignoring spike: 1 1 4a3cdfef .

lirc_serial: port 03f8 already in use lirc_serial: use 'setserial devttySX uart none' lirc_serial: or compile the serial port driver as module and lirc_serial: make sure this module is loaded first .lirc_serial port already in use.
Oct 5 07:46:07 arvdr kernel: lirc_serial: port 03f8 already in use. Oct 5 07:46:07 arvdr kernel: lirc_serial: use 'setserial devttySX uart none' Oct 5 07:46:07 arvdr kernel: lirc_serial: or compile the .pnp: match found with the PnP device '00:09' and the driver 'serial' lirc_serial: no version for " lirc_unregister_plugin" found: kernel tainted. lirc_serial: port 03f8 already in use lirc_serial: use .

(make menuconfig) Device Drivers ---> Multimedia Support ---> Remote Controller Support ( im Kernel) . Nov 11 19:40:56 localhost kernel: [ 52.220842] lirc_serial: port existence test failed .lirc_serial port existence test failed.
[12187.960012] lirc_serial: port 03f8 already in use [12187.960018] lirc_serial: use 'setserial devttySX uart none' [12187.960022] . [ 172.439411] lirc_serial: port existence test failed, cannot . It's currently syncing to our mirrors and should show up >>> shortly in the testing repository: . signature andor required key missing - tainting kernel [ 1631.901496] lirc_serial: port existence test .

<< Go back to the previous page